Flight level

src: www.chinarma.cn

In aviation and aviation meteorology, a flight level (FL) is defined as a vertical altitude at standard pressure, nominally expressed in hundreds of feet. The pressure is computed assuming an International standard sea-level pressure datum of 1013.25 hPa (29.92 inHg), and therefore is not necessarily the same as the aircraft's actual altitude either above mean sea level or above ground level.

Video Flight level

Background

Flight levels are used to ensure safe vertical separation between aircraft, despite natural local variations in atmospheric air pressure. Historically, altitude has been measured using a pressure altimeter, which is essentially a calibrated barometer. An altimeter measures ambient air pressure, which decreases with increasing altitude following the barometric formula. It then calculates and displays the corresponding altitude.

To display altitude above sea level, a pilot must calibrate the altimeter according to the local air pressure at sea level, to take into account natural variation of pressure over time and in different regions. If this is not done, two aircraft could be flying at the same altitude even though their altimeters appear to show that they are at considerably different altitudes.

Flight levels solve this problem by defining altitudes based on a standard air pressure at sea-level. All aircraft operating on flight levels calibrate to this setting regardless of the actual sea level pressure.

Maps Flight level

Definition

Flight levels are described by a number, which is this nominal altitude (or, pressure altitude) in hecto-feet, while being a multiple of 500 ft, therefore always ending on 0 or 5. Therefore, a pressure altitude of, for example, 32,000 feet is referred to as "flight level 320".

Flight levels are usually designated in writing as FLxxx, where xxx is a two or three-digit number indicating the pressure altitude in units of 100 feet. In radio communications, FL290 would be pronounced as "flight level two nine(r) zero." The phrase "flight level" makes it clear that this refers to the standardized pressure altitude.

src: www.challenger.ca

Transition altitude

While use of a standardised pressure setting facilitates separation of aircraft from each other, it does not provide the aircraft's actual height above ground. At low altitudes, the altimeter is commonly set to show the altitude above sea-level, which can be directly compared to the known elevation of the terrain. The pressure setting to achieve this varies with weather conditions. It is called QNH ("barometric pressure adjusted to sea level") or "altimeter setting" and the current local value is available from various sources, including air traffic control and the local METAR-issuing station.

The transition altitude (TA) is the altitude above sea level at which aircraft change from the use of local barometer derived altitudes to the use of flight levels. When operating at or below the TA, aircraft altimeters are usually set to show the altitude above sea level. Above the TA, the aircraft altimeter pressure setting is normally adjusted to the standard pressure setting of 1013.25 hectopascals (millibars) or 29.92 inches of mercury and aircraft altitude will be expressed as a flight level.

In the United States and Canada, the transition altitude is 18,000 ft (5,500 m). In Europe, the transition altitude varies and can be as low as 3,000 ft (910 m). There are discussions to standardize the transition altitude within the Eurocontrol area.

On 25 November 2004 the Civil Aviation Authority of New Zealand raised New Zealand's transition altitude from 11,000 to 13,000 feet (3,400 to 4,000 m) and changed the transition level from FL130 to FL150.

The transition level is the lowest flight level above the transition altitude. The table below shows the transition level according to transition altitude and QNH. When descending below the transition level, the pilot starts to refer to altitude of the aircraft by setting the altimeter to the QNH for the region or airfield.

The transition layer is the airspace between the transition altitude and the transition level.

According to these definitions the transition layer is 0-500 feet (0-152 m) thick. Aircraft are not normally assigned to fly at the "'transition level'" as this would provide inadequate separation from traffic flying on QNH at the transition altitude. Instead, the lowest usable "'flight level'" is the transition level plus 500 ft.

However, in some countries, such as Norway for example, the transition level is determined by adding a buffer of minimum 1,000 ft (depending on QNH) to the transition altitude. Therefore, aircraft may be flying at both transition level and transition altitude, and still be vertically separated by at least 1,000 ft. In those areas the transition layer will be 1,000-1,500 ft thick, depending on QNH.

In summary, the connection between "'transition Altitude'" (TA), "'transition layer'" (TLYR), and "'transition level'" (TL) is

TL = TA + TLYR

src: i.vimeocdn.com

Quadrantal rule

This rule is no longer active.

This rule applied to IFR flights in the UK both in and outside of controlled airspace except that such aircraft may be flown at a level other than required by this rule if flying in conformity with instructions given by an air traffic control unit, or if complying with notified en-route holding patterns or holding procedures notified in relation to an aerodrome. The rule affected only those aircraft operating under IFR when in level flight above 3,000 ft above mean sea level, or above the appropriate transition altitude, whichever is the higher, and when below FL195 (19,500 ft above the 1013.2 hPa datum in the UK, or with the altimeter set according to the system published by the competent authority in relation to the area over which the aircraft is flying if such aircraft is not flying over the UK.)

The rule was non-binding upon flights operating under visual flight rules (VFR).

Minimum vertical separation between two flights abiding by the UK Quadrantal Rule is 500 ft (note these are in geopotential foot units). The level to be flown is determined by the magnetic track of the aircraft, as follows:

• Magnetic track 000 to, and including, 089° - odd thousands of feet (FL70, 90, 110 etc.)
• Magnetic track 090 to, and including, 179° - odd thousands plus 500 ft (FL75, 95, 115 etc.)
• Magnetic track 180 to, and including, 269° - even thousands of feet (FL80, 100, 120 etc.)
• Magnetic track 270 to, and including, 359° - even thousands plus 500 ft (FL85, 105, 125 etc.)

The UK abolished the quadrantal rule on 2 April 2015 and has adopted the semi-circular rule to align with other countries abroad.

src: www.mccpilotlog.net

Semicircular/hemispheric rule

(Versions of this apply to IFR in the UK inside controlled airspace and generally in the rest of the world)

The semicircular rule (also known as the hemispheric rule) applies, in slightly different version, in all of the world, including in the UK inside controlled airspace.

The standard rule defines an East/West track split:

• Eastbound - Magnetic track 000 to 179° - odd thousands (FL 250, 270, etc.)
• Westbound - Magnetic track 180 to 359° - even thousands (FL 260, 280, etc.)

At FL 290 and above, if Reduced Vertical Separation Minima are not in use, 4,000 ft intervals are used to separate same-direction aircraft (instead of 2,000 ft intervals below FL 290), and only odd flight levels are assigned, independent of the direction of flight:

• Eastbound - Magnetic track 000 to 179° - odd flight levels (FL 290, 330, 370, etc.)
• Westbound - Magnetic track 180 to 359° - odd flight levels (FL 310, 350, 390, etc.)

Countries where the major airways are oriented north/south (e.g., New Zealand; Italy; Portugal; France) have semicircular rules that define a North/South rather than an East/West track split.

In Italy, France and Portugal, for example, southbound traffic uses odd flight levels; in New Zealand, southbound traffic uses even flight levels. In Europe commonly used ICAO separation levels are as per the following table:

src: airway.uol.com.br

Reduced vertical separation minima

Reduced Vertical Separation Minima (RVSM) reduces the vertical separation above FL 290 to 1,000 ft. This allows aircraft to safely fly more optimum routes, gain fuel savings and increase airspace capacity by adding new flight levels. Only aircraft that have been certified to meet RVSM standards, with several exclusions, are allowed to fly in RVSM airspace. It was introduced into the UK in March 2001. On 20 January 2002, it entered European airspace. The United States, Canada and Mexico transitioned to RVSM between FL 290 and FL 410 on 20 January 2005, and Africa on 25 September 2008.

• Track 000 to 179° - odd thousands (FL 290, 310, 330, etc.)
• Track 180 to 359° - even thousands (FL 300, 320, 340, etc.)

At FL 410 and above, 4,000 ft intervals are resumed to separate same-direction aircraft and only odd Flight Levels are assigned, depending on the direction of flight:

• Track 000 to 179° - odd flight levels (FL 410, 450, 490, etc.)
• Track 180 to 359° - odd flight levels (FL 430, 470, 510, etc.)

src: flightleveldesign.com

Metric flight levels

China, Mongolia, Russia and many CIS countries have used flight levels specified in metres for years. Aircraft entering these areas normally make a slight climb or descent to adjust for this, although Russia and some CIS countries started using feet above transition altitude and introduced RVSM at the same time on 17 November 2011.

Mongolia, North Korea, Kyrgyzstan, Kazakhstan, Tajikistan and Uzbekistan, and Turkmenistan

The flight levels below apply to Mongolia, North Korea, Kyrgyzstan, Kazakhstan, Tajikistan and Uzbekistan and 6,000 m or below in Turkmenistan (where feet is used for FL210 and above). Flight levels are read as e.g. "flight level 7,500 metres":

People's Republic of China

The flight levels below apply to People's Republic of China, not including Hong Kong. To distinguish flight levels in feet, flight levels are read without "flight level", e.g. "one two thousand six hundred metres" or in Chinese "???" or "???????" for 12,600m. RVSM implement in China at 1600 UTC 21 Nov 2007. The aircraft fly in feet according to the table below will have differences between the metric readout of the onboard avionics and ATC cleared flight level, however the differences will never be more than 30 metres.

src: flightleveldesign.com

Flight levels in Russian Federation

On 5 September 2011 the government of the Russian Federation issued decree No743, pertaining to the changes in the rules of use of the country's airspace. The new rules came into force on 17 November 2011, introducing a flight level system similar to the one used in the West. RVSM has also been in force since this date.

The following table is true for IFR flights:

The new system would eliminate the need to perform climbs and descents in order to enter or leave Russian airspace from or to jurisdictions following the Western standard.

From February 2017, Russia is changing to use QNH and Feet below the Transition Level. The first airport to use this is ULLI/St. Petersburg.

src: i.ytimg.com

See also

• Flight planning
• Gillham code

src: prd-wret.s3-us-west-2.amazonaws.com

References

Source of the article : Wikipedia